Yes, the B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 is the correct system for both your 2016 Ultra Limited(FLHTK) and 2021 Road Glide Special(FLTRXS). It fits all FL Touring models Harley Davidson motorcycles.
Your 2014 CVO Breakout(FXSBSE) will use the B&W Biker Bar Motorcycle Tie-Down System # BWMC2302. This fits Harley FX, FLST, and VR models.
An additional B&W Biker Bar Motorcycle Tie-Down System Base # BWMC2300 can be used if you have multiple trailers and do not want to... view full answer...
I reached out to CargoSmart and found that there is no weight capacity rating for the CargoSmart Motorcycle Wheel Chock for E-Track or X-Track Systems # 3481731 since it is only meant to stabilize your motorcycle. The limiting factor would be the E-track in this case.
Assuming you are using the single slot E-track tie-down points like the Snap-Loc E-Track Tie-Down Anchor # SLSB you shouldn't have any problems. Although I do not know the capacity of what you have, each of these has a safe... view full answer...
Each model of the B&W Biker Bar Motorcycle Tie-Down System for Trailers will use two anchor plates # BWMC2305 to connect to. The anchors would be secured to the underbelly of the trailer making it hard to use in multiple locations, so you'd really need to buy a set for each trailer you plan to haul with. The base bolts down to the anchors so if you really wanted to you can remove it from the anchors but this would also be somewhat of a hassle. view full answer...
The 2015 Harley Davidson Ultra Limited Low FLHTKL is classified as a touring bike, so you'd want to use the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301. I've linked an installation video of this part for you to check out as well. view full answer...
The B&W Biker Bar Motorcycle Tie-Down Systems such as # BWMC2302 are designed at a specific height to attach to the frame of the bikes they were made for. Flat tires would make the bike lower and cause it not to fit the Bike Bar properly. You would need to air up the tires or place boards or something under the tires so the bike sits up at the proper height. You would want the boards to be secured to the trailer floor as well to avoid slipping in transit. view full answer...
I am not sure I understand what you are asking. The Ram Gooseneck to 5th Wheel Trailer Coupler Adapter part # KPG5-R30 installs on the trailer, not the tow vehicle. It is designed to replace the gooseneck coupler on the trailer and allow for connection to a 5th wheel hitch as opposed to connection with a gooseneck hitch ball. The old coupler will need to be cut off and the new outer tube will need to be welded on the trailer by a professional welder. The inner tube will then slide in the... view full answer...
I recommend using the Tekonsha ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT for your 2001 Harley Davidson Road King as we will not have a custom fit wiring kit. This kit features wiring sensors that will detect the power running through the taillight wires. This protects you from having to splice into the wiring or risk overloading the wiring that Harley installed.
A Mounting Bracket # 18144 can be used to secure the 4-way plug on the back of your Road King. view full answer...
I reached out to my contact at B&W for this recommendation. The B&W # BWMC2301 B&W Biker Bar is the correct mount for both of your Harleys.
I have attached a link to the installation instructions and several videos about using this product. the install seems pretty straight forward. view full answer...
The Adco SFS AquaShed Cover for Bumper Pull Trailer - Up to 16' Long - Gray # 290-46004 will fit trailers up to 106" wide. The Adco SFS AquaShed has cinching ropes and weighted straps to secure the cover on your trailer so that it doesn't billow in the wind, which might cause tears, so your cover will always be secured tightly to the trailer. view full answer...
I spoke to my contact at B&W and they informed me that the correct B&W Biker Bar Motorcycle Tie-Down System for your Harley Davidson Electra Glide Limited Low is the part # BWMC2301. I have attached a sample installation video for you as well. view full answer...
Yes. The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301 will work on Harley Davidson trikes manufactured before 2014, so your 2014 Harley Davidson Tri-Glide Ultra without any issues. The Biker Bar will connect at the same place on your trike as it would on a regular motorcycle since the frame in that spot is the same. view full answer...
The 2014 Harley Davidson Fat Boy Lo is considered a Softail. This means that the correct biker bar for your Harley is the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Softail, Dyna, V-Rod # BWMC2302. view full answer...
The 2003 Harley Heritage Springer would fall into the Softail, Dyna, and V-Rod category as far as the Bike Bars go so you would need model # BWMC2302.
Specs on this model are:
Fits frame tube diameters between 1-1/4" - 1-3/8"
Fits frame width between 10" - 14" view full answer...
While we do not have a trailer hitch for your 2020 Harley Davidson TriGlide I can help you with all the wiring you will need. We only have universal wiring so you would first need a 4-Way # C59236 which you would then use the 6-Way Upgrade # ETBC6 since you are adding a Brake Controller # RED52VR. The 6-way round is generally the type of connector for motorcycle trailers using brakes as they do not require the reverse circuit wiring. view full answer...
The B&W Biker Bar that you should be using for your 2010 Ultra Classic is the part # BWMC2301 but for your 2014 Softail Deluxe you need the Biker Bar # BWMC2302 instead. Good news is that both options use the same base system so you just need to replace the actual bar instead of the entire kit and for that you need the Replacement Bar # BWMC2302B. This then gives you the entire setup for your Softail Deluxe. view full answer...
The B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 will work great with your Road King FLHR that has the rear air suspension just as long as your frame tubing diameter is 1-1/8-inches or 1-1/4-inches and that tubing is spaced apart 10-inches to 14-1/2-inches at the bottom of the frame.
You will want to have the bike as low to the deck as possible for the lowest center of gravity. The installation instructions are linked for you along with a video. view full answer...
In order to find if the B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 will fit your 2021 Harley Davidson Tri Glide you will need to measure. You will be able to use this system as long as your frame tube diameter is 1-1/8" - 1-1/4" and your frame width is 10" - 14-1/2". view full answer...
The B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 referenced in your question is confirmed to fit all model years of the Harley Davidson FL Series Bikes, including your FLHTK.
This tie-down system will do a great job of securing your bike without the need for any straps or chocks. You will simply mount the clamping bar to your bike, drive over the trailer-mounted plate, and your motorcycle will automatically latch into place. The neoprene-lined clamps on the bar won't scratch your... view full answer...
The B&W Biker Bar Motorcycle Tie-Down System Base with Anchor Plates # BWMC2300 will fit your 2010 Harley Davidson Ultra Classic. This will be just the base mount, though.
If you are wanting the complete system that will be the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301. This system includes the base mount and the clamping bar that will mount on your bike. view full answer...